世界杯2022买球_足球世界杯下注

世界杯2022买球
热线电话:400-879-1999 山汽官方微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 行业新闻 >

自上料搅拌车在卸料时需要注意什么?

所属分类:行业新闻 发布时间:2022-05-13 来源: 浏览量:18

目前生产企业对自上料搅拌车钢制水箱防锈处理的方式主要有两种:
At present, there are two main ways for manufacturers to deal with the rust prevention of the steel water tank of the self loading mixer:
一是镀锌处理,自上料搅拌车水箱做好后送到镀锌厂电镀,这种方法成本较高,且费时。
One is galvanizing treatment, which is sent to the galvanizing plant for electroplating after the water tank of the feeding mixer is completed. This method has high cost and time-consuming.
二是企业自行做防腐处理,酸洗除锈→浸泡磷化液中→水箱内倒入防锈漆后再倒出→烘干。这种处理因不是厂家的规范操作,质量就难以得到保证。关键是目前大多数专用车企业没有酸洗、磷化工装,基本上未对自上料搅拌车钢制水箱做防腐处理。钢铁生锈的反应机理为铁分子与空气中的氧气、水发生氧化反应,所以只要有空气和水的存在,钢制水箱生锈就在所难免。好在为了保证标准压力下水箱的强度,所用钢板至少有 厚度,因此水箱在使用寿命内不容易因锈蚀而漏水,即使坏了,维修或更换也较方便,且价格低廉。
Second, the enterprise shall carry out anti-corrosion treatment by itself, pickling and derusting → soaking in phosphating solution → pouring antirust paint into the water tank and then pouring it out → drying. Because this treatment is not the standard operation of the manufacturer, the quality is difficult to be guaranteed. The key is that at present, most special vehicle enterprises do not have pickling and phosphorus chemical equipment, and basically do not do anti-corrosion treatment for the steel water tank of self loading mixer truck. The reaction mechanism of steel rust is the oxidation reaction between iron molecules and oxygen and water in the air. Therefore, as long as there is air and water, the rust of steel water tank is inevitable. Fortunately, in order to ensure the strength of the water tank under standard pressure, the steel plate used is at least thick, so the water tank is not easy to leak due to corrosion within its service life. Even if it is broken, it is convenient to repair or replace, and the price is low.
自上料搅拌车在卸料时的注意事项:
Precautions for self loading mixer during unloading:
1、自上料搅拌车卸料前让搅拌罐全速运转一两分钟。让混凝土充分搅拌,必要时可以加一些水,让混凝土搅拌得更均匀,也方便卸料。
1. Let the mixing tank run at full speed for one or two minutes since the loading mixer is unloaded. Allow the concrete to be fully mixed. If necessary, add some water to make the concrete mix more evenly and facilitate unloading.
2、放料前先把出料斗溜槽打湿。放料时把车尽量停在平地上放料前先把出料斗溜槽打湿,方便清洗。
2. Wet the chute of the discharge hopper before discharging. When discharging, park the car on the flat ground as far as possible. Wet the chute of the discharge hopper before discharging to facilitate cleaning.
3、卸料不要大意和放料工打好关系。放料时自己看着,免得放料工乱操作放料操作杆,每次自上料搅拌车罐子正反转中间位子时停一下,保护减速机,托轮等。与放料工打好关系,卸料时也不要睡的太熟,万一工人闹情绪,把你自上料搅拌车放到工地不转罐子,造成闷罐就麻烦了。
3. Don't be careless in discharging and have a good relationship with the discharging worker. Watch by yourself when discharging, so as to prevent the discharging worker from operating the discharging operation lever disorderly. Stop every time when the tank of the charging mixer is in the middle position of forward and reverse rotation, so as to protect the reducer, supporting wheel, etc. Make a good relationship with the discharging worker and don't sleep too well during unloading. In case the worker is in a mood, put your self loading mixer on the construction site and don't turn the tank, resulting in the trouble of stuffy tank.
4、自上料搅拌车搅拌罐一定要仔细地冲洗干净。洗罐子时要仔细的冲洗干净,并把水反复的正反转两次,再放出来,一趟时把水箱的水全部放进罐子,再回到站加水清洗罐子。
4. The mixing tank of the self loading mixer must be washed carefully. When washing the jar, wash it carefully, and repeat the positive and negative rotation of the water twice, and then release it. In one trip, put all the water in the water tank into the jar, and then return to the station to add water to clean the jar.
本文的精彩内容由自动上料搅拌车提供知识提供,本网站还有很多的精彩内容,更多的内容您可以点击进入:/ 我们有专门的客服为您解答问题
The wonderful content of this article is provided by the knowledge of automatic feeding mixer. There are many wonderful contents on this website. You can click to enter more contents: / We have special customer service to answer your questions
热门产品 / HOT PRODUCT

 

首页 产品 电话 置顶
Baidu
sogou